Jump to content

Recommended Posts

I'm in process of choosing new laminate flooring for my house.

Exciting but as usual it's a bit daunting as there are so many to choose from and i don't know what i am doing!


I found one that I really like (width, colour and pattern) and it's cheap! but the problem is it's TOO cheap.

It usually ranges between ?5 - ?25 per square meter but this one is at ?4.50


Has anyone bought very cheap laminate and have regrets?


Too thin?

Gets dirty easily?


I'm quite concerned about the second point as I am leaning towards having white/grey flooring.

Probably a bad idea but it looks so lovely.

Link to comment
https://www.eastdulwichforum.co.uk/topic/33870-cheap-laminate-problems/
Share on other sites

I found laminate warps easily and looks shabby pretty quickly.


I now only buy engineered wood flooring, but it's much more expensive (?40 per sq m or so).


Sounds a bit pompous perhaps, but at ?4.50 a sq m, it's probably worth the risk? If you don't like it, it's not the end of the world.

Depends which room- I've had cheapo Ikea stuff down for 15 years now in a room with light-ish use and despite beer and tea being spilled on it there is no warping. And it has had a piano on it- both across the planks and parallel to the planks ( and one of the pianos was an old iron framed Victorian job) for the duration. The beauty is there is hardly any dust!

Agree with the points about quick fix, but no good for longer/ heavy use. If it's for longer, no matter what you chose, invest in good underlay - otherwise even expensive laminate will wear badly. We actually have bamboo flooring in our house - looks lovely like wood and extremely hard wearing. Cost around ?15/m2, but no good for a bathroom. There are many different types - pm me, if you want to know more, happy to share findings of my research (and no, am not on commission ;) )

mx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Discussions

    • @malumbu as your questions would take us off topic on so many tangents, I will defer my response to a more appropriate thread.
    • @vladi it would be good to hear your views on my comments (a) the damage to society of austerity and (b) how poorly the Tories handled our economy prior (and post if you like) Covid Do you believe in climate change and if so what should we be doing?  I'd disgusted by Badenock aping Reform.  
    • The Labour Party is a poor advert for the Labour Party. I think this council just reflects the national picture. 
    • Covid certainly was a big factor in creating the debt burden however the Govt continues to expand the hole by giving crazy subsidies to suppliers of so-called "low carbon" electricity eg wind turbine farms, solar panels and worst of all - Drax power station. According to the Renewable Energy Foundation, the UK currently spends around £25.8 billion per year on renewable electricity subsidies, covering both direct and indirect schemes. Drax gets just shy of £1 billion a year to use import & burn wood pellets which are produced in a highly energy consumptive process.  Wood pellets used by Drax  are produced through a multi-stage process that converts wood material into dense, energy-rich fuel. The raw material typically comes from, offcuts, and sawmill by-products rather than high-value timber. Logs are first collected from forests across the U.S. South and West Coast, ‘ At pellet plants, the wood is debarked and chipped into small pieces before being dried to reduce moisture content. The drying process often uses waste wood as a heat source to improve efficiency and lower emissions. Once dried, the wood chips are milled into a fine powder, then compressed at high pressure through a die to form small cylindrical pellets, each around 6–8 mm in diameter. The natural lignin in the wood binds the pellets together, eliminating the need for chemical additives. After production, pellets are cooled, screened to remove dust and fines, and stored in large silos. They are then loaded into trucks or railcars and transported across the United States from west to east to dedicated export terminals.. At these terminals, pellets are conveyed into covered storage domes or silos to protect them from moisture, since wet pellets can disintegrate and pose safety risks. From there, bulk carriers transport the pellets across the Atlantic to the United Kingdom. Drax even had to develop specialized port and rail infrastructure to handle pellet imports , including large storage domes at  Immingham and direct rail links to its  power station. It's no wonder wed have the highest energy costs in all of Europe!
Home
Events
Sign In

Sign In



Or sign in with one of these services

Search
×
    Search In
×
×
  • Create New...