Jump to content

Recommended Posts

Hi, I wonder if you could help.

We have a kitchen side return completed by the previous owners. Also, our neighbors have extended into the garden, building a party wall we can share. We want to build an extension (going out 3 meters approximately into the back garden), but are not sure how much it would cost. One builder quoted me 30-50k, but my husband thinks it can easily run over 100k. Where do we get advise on approximate cost before we commission any architectural plans? We do not want to be quoted a much lower price initially and then overspending.

Thank you for your help!

Link to comment
https://www.eastdulwichforum.co.uk/topic/291483-kitchen-extension-how-much/
Share on other sites

Going back as well as to the side is significantly more expensive because the steelwork is more complex and because of the extra foundation work. Overall cost is all down to fit and finish. I?m sure you could get a basic side return built for ?30-50k but put in nice glazing, a new kitchen, decent new floor etc it?ll easily run to ?100k

have you spoken to a company about the build cost? I did a side return (nothing fancy, but nice quality) and it cost me ?60k without any of the internal stuff. Then I spent ?30k on a kitchen, ?6k on my floor etc etc. It can easily go above ?100k I would say but you need a company who can help you keep the fluff to a minimum. I used hometales for mine and they advised on cost before I went ahead and they were spot on. Maybe try contacting them or similar?


www.hometales.co.uk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Discussions

    • If you want to change a radiator and it is the same size, pretty straight forward.  isolate by turning the two valves, one is straight forward hand twist, the other side you need to take the cap off and get an adjustable spanner and turn till closed.  Both clockwise. Use the same spanner to undo the large nuts that fix the radiator to the pipework, open the bleed valve, get a flatish container to catch the water which is likely to be a grotty black, sheets/plastic underneath to protect floor/floor covering.  Then jiggle off, tipping as quick as you an into your water container. Fingers crossed it will be the same back plate fitting.  If not you will have to take the old one off and fix the new one. Replacement is a reverse, allowing the rad to refill and let the air out. No naked flames involved. If it is a different size I can advise on that too. Lots on line too: https://www.toolstation.com/help-and-advice/how-to-guides/how-to-remove-radiator?gad_source=1&gad_campaignid=19747119835&gclid=CjwKCAiAkvDMBhBMEiwAnUA9BR26YwBA6kOfcR4-JVxfJEjWdhRk6j0imCNcsIfu064wHN54-cs10xoCZ4cQAvD_BwE Although this is for a pressurised (combi) system where you need to get it back to pressure.  Pretty simple.  I don't bother with jointing compound.    
    • Fair enough - I'm absolutely wrong on that one. 👍
    • I'm still completely unclear what happened, apart from that a car apparently crashed into a lamp post opposite the Co-op. I presume the one in Lordship Lane, though the OP doesn't say. Was it speeding? Did it swerve to avoid someone who ran into the road? Did something go wrong with its brakes or steering? Did the driver have a medical emergency or fall asleep or got  distracted by something? Was there something slippery on the road surface? Was the driver hurt? Were any passengers hurt? Were any pedestrians or other road users hurt? Were there any witnesses? 
    • confused by the question?
Home
Events
Sign In

Sign In



Or sign in with one of these services

Search
×
    Search In
×
×
  • Create New...