Jump to content

Recommended Posts

We're planning on having sanded/varnished floorboards in the lounge of our house... so far so good... but in front of the fire place, the hearth (which I think would have originally been a piece of stone flush with the floorboards) has been replaced with some old bits of tatty wood.


I think it would look much better with a piece of stone/slate in there... and besides, I am assuming that a stone hearth in front of the fireplace is mandatory if we want an actual fire or stove at some point.


So what's the best thing to do? Find someone who can supply a piece of stone of the correct size and fit it? Or is it better to buy a standard "off-the-shelf" one, and cut back the floorboards to fit around it?

Link to comment
https://www.eastdulwichforum.co.uk/topic/35598-fireplace-hearth-advice/
Share on other sites

Actually there is already stone inside the fireplace itself... but not in front of the fireplace. And I'm talking about stone which is flush with the floor, not sitting above it.


(Come to think of it, the fireplace itself might contain poured concrete rather than a piece of stone)

Probably, therefore you shouldn't let that drive the aesthetic. A nice piece of stone sat next to some old concrete screed? When it was a working fireplace you wouldn't have seen the screed, therefore it wasn't an issue.

It's six of one, half a dozen etc if you go with bespoke or ready made.

Personally I would think about the overall desired finish and work back from that.

For instance does it, or will it have a fireplace surround to it?

If you had a stove would you want some space for decorative log storage to sit on the hearth.

These things will impact on the size of the hearth.

Personally I think it would look a lot better if finished like the above photo, all-in one, going into the fireplace, therefore it will need to be templated to suit. As for finishing flush or not, that's up to you, but the easiest would be to lay the stone on top of the screed and floor boards if required. If you wanted it flush, rather than messing with the floorboards, the screed could probably be lowered so that the stone sits flush...

its also good to think what you are going to put in the hearth- either now or in the future- as there are regulations esp for gas fittings/ coal effect fire etc. A real fire can get very hot and you must use the correct type of stone ( as we found out to our cost)
Having thought about it more (and to answer your original question) if you are happy with the size of the existing hearth (ignoring the rear screed for now) it will be better to get a bespoke piece of stone made rather than cutting into the existing floorboards to fit an off-the-shelf piece of stone. The reason being that the hearth and floorboards will have their own support structure beneath which will have to be mucked around with in order to get the new off-the-shelf hearth in...

My current thinking is that I should get a piece of stone cut to fit the existing hole in front of the fireplace... at least then it will look respectable once the floor is sanded and finished. In the future we may want to put an extra raised hearth on top of it (as in your photo, RD). This will mean ripping out the existing surround and then re-mounting it higher up... but the fact that there's a non-combustible hearth beneath it should mean we're safe if/when a fire goes in.


So I guess my next question is... who knows of someone who can supply a slab of slate to my specified dimensions for a decent price?

I haven't got any names of suppliers (worth checking local stone masons though as they might have off-cuts), but if you do end up taking responsibilty for supplying the dimensions, measure the diagonals as well as the sides, as the rectangle may not be square...if you know what I mean :)

Either: You make a template out of clear Correx sheet


Mark the finished edges (the ones that you'll see) onto the template with black Sharpie. Spec a pencil round edge around the top edge , again where you'll see


Go down to Marble City Wandsworth or another stonemason and they'll quote/supply you


Honed black slate is usual and not expensive, finish it with this stuff http://www.amazon.co.uk/HG-Satin-Polish-Golvpolish-litre-P14-PLEASE/dp/B001DYUMD2


Once fitted mask the edges and fill the gaps with black silicon and tool wet into shape. Carefully remove and leave to cure.



Or: Get a company to template, supply, fit. It's a standard service. I use Paul Challen in Arundel as they work all over London.


Hope this helps


Pm me for any other details if you like.

Thanks nette. But for now I just need a rectangle, so template shouldn't be necessary. I actually came across marble city earlier when googling for 'stone hearth london', so will be sure to get a quote from them. Perhaps at a later date I'll go for a "T" shaped piece to lay on top of it.


Will probably fit myself... just a matter of ripping out the "placeholder" wood, squirting with adhesive, and lowering into place. In theory.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Discussions

    • Hello! We are relocating abroad and so will be withdrawing our two children (ages 4 and 6) from St Dunstan’s College (Catford). If any family is considering enrolling children of a similar age, now would be an excellent opportunity—we’re required to pay full‑term fees unless the places are taken. Please get in touch if you’re interested or know someone who might be. Thank you!
    • Hi  I really thought I'd seen a more recent post on the forum about home education meet ups. I can't find it though. Hope some of these might provide leads. https://www.eastdulwichforum.co.uk/topic/137603-home-schooling-advice-anyone-wants-to-do-it-together/#comment-1092093 Very old post but group seems still to exist: https://www.eastdulwichforum.co.uk/topic/92044-home-education-local-group/#comment-954837 You could try contacting this forum member: https://www.eastdulwichforum.co.uk/topic/325368-classroom-support-for-home-education-community/#comment-1621064 Two of these left for right now: https://www.eastdulwichforum.co.uk/events/event/1025-🌟-teens-11-try-painting-sculpture-street-art-at-holiday-workshops/
    • Thanks for your reply. I’ve subscribed to Ancestry a few times in the past but felt I wasn’t using it enough to warrant keeping up the subscription.    
    • Hi, I saw your post and just wanted to say that the incident you’re referring to did happen in the late 1980s at Dawson’s Heights. The person involved was named Carl Salawa, and he had just turned 18 years old at the time. Like you, I haven’t been able to find any news articles or official reports about it, If anyone remembers anything more about that time or incident, I’d really appreciate hearing about it. Thanks for sharing what you were told—it means a lot to know others remember.
Home
Events
Sign In

Sign In



Or sign in with one of these services

Search
×
    Search In
×
×
  • Create New...