What's on in East Dulwich
Playing a gig? Holding a fair? Spread the word about it here.
Check out our brand new Events Calendar. An organised version of What's on in East Dulwich.
Event hosts - please also add your events to the calendar.
13,514 topics in this forum
-
- 0 replies
- 334 views
-
- 0 replies
- 499 views
-
- 1 reply
- 417 views
-
- 0 replies
- 335 views
-
- 0 replies
- 440 views
-
- 0 replies
- 304 views
-
- 0 replies
- 260 views
-
- 0 replies
- 295 views
-
- 0 replies
- 429 views
-
- 0 replies
- 331 views
-
- 0 replies
- 328 views
-
- 1 reply
- 306 views
-
- 0 replies
- 355 views
-
- 0 replies
- 291 views
-
- 0 replies
- 325 views
-
- 0 replies
- 318 views
-
- 0 replies
- 350 views
-
- 4 replies
- 542 views
-
- 0 replies
- 364 views
-
SLDA Easter Dance Camp @ Ivydale Primary School, Inverton Building *4th-8th April 2022 9.00am-3.00pm
- 0 replies
- 298 views
-
- 0 replies
- 313 views
-
- 0 replies
- 341 views
-
- 0 replies
- 333 views
-
- 0 replies
- 390 views
-
- 0 replies
- 296 views
-
-
Latest Discussions
-
If you want to change a radiator and it is the same size, pretty straight forward. isolate by turning the two valves, one is straight forward hand twist, the other side you need to take the cap off and get an adjustable spanner and turn till closed. Both clockwise. Use the same spanner to undo the large nuts that fix the radiator to the pipework, open the bleed valve, get a flatish container to catch the water which is likely to be a grotty black, sheets/plastic underneath to protect floor/floor covering. Then jiggle off, tipping as quick as you an into your water container. Fingers crossed it will be the same back plate fitting. If not you will have to take the old one off and fix the new one. Replacement is a reverse, allowing the rad to refill and let the air out. No naked flames involved. If it is a different size I can advise on that too. Lots on line too: https://www.toolstation.com/help-and-advice/how-to-guides/how-to-remove-radiator?gad_source=1&gad_campaignid=19747119835&gclid=CjwKCAiAkvDMBhBMEiwAnUA9BR26YwBA6kOfcR4-JVxfJEjWdhRk6j0imCNcsIfu064wHN54-cs10xoCZ4cQAvD_BwE Although this is for a pressurised (combi) system where you need to get it back to pressure. Pretty simple. I don't bother with jointing compound. -
By Dogkennelhillbilly · Posted
Fair enough - I'm absolutely wrong on that one. 👍 -
I'm still completely unclear what happened, apart from that a car apparently crashed into a lamp post opposite the Co-op. I presume the one in Lordship Lane, though the OP doesn't say. Was it speeding? Did it swerve to avoid someone who ran into the road? Did something go wrong with its brakes or steering? Did the driver have a medical emergency or fall asleep or got distracted by something? Was there something slippery on the road surface? Was the driver hurt? Were any passengers hurt? Were any pedestrians or other road users hurt? Were there any witnesses? -
-