Jump to content

Recommended Posts

Just to give u a chuckle :


(1) got real mean on that water feed pipe stop tap. Hairdryer for 10 mins, bought a basin wrench and oil and now buggered my wrist.


(2) noticed a small hole in the wall where all the piping was heading


(3) Got new bats for the torch, guessed it? Yeah wrong pipe. This one that i've been trying to bore into the wall feeds the tank from the mains. I turned of both tank pipes ages ago - 1 in 1 out, except they must have both been out, 1 to boiler 1 to appliances. Tits.


(4) SO I guess there simply isn't a stop tap for the kitchen sink except the mains outside the house.


All I want to do is remove the kitchen sink units. The sodding kitchen tap nuts are limed up and can't undo. I wonder if I can just cut the pipe and cap it somehow...

DJKillaQueen Wrote:

-------------------------------------------------------

> Or just freeze the pipe up to the sink taps, cut

> it and cap it (use isolation valves and you can

> turn them on if you want to get some water at any

> point).



OOooooo it's happening again...


" Can I buy you a drink? "


Nette.(?)

Loz Wrote:

-------------------------------------------------------

> Have you got a thing for plumbers, Nette, or do

> you just need your pipes, erm... seen to?


She's more than a plumber, she's bloody WONDERWOMAN.


I some need pipe.


Nette.::o

Huguenot Wrote:

-------------------------------------------------------

> Alas Annette, I fear DJKQ plumbs for the other

> side ;-)



Surely there is a convertor tool available, a coupling even ?


* twiddles with stopcock *


What ?


Nette.:-$

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Discussions

    • If you want to change a radiator and it is the same size, pretty straight forward.  isolate by turning the two valves, one is straight forward hand twist, the other side you need to take the cap off and get an adjustable spanner and turn till closed.  Both clockwise. Use the same spanner to undo the large nuts that fix the radiator to the pipework, open the bleed valve, get a flatish container to catch the water which is likely to be a grotty black, sheets/plastic underneath to protect floor/floor covering.  Then jiggle off, tipping as quick as you an into your water container. Fingers crossed it will be the same back plate fitting.  If not you will have to take the old one off and fix the new one. Replacement is a reverse, allowing the rad to refill and let the air out. No naked flames involved. If it is a different size I can advise on that too. Lots on line too: https://www.toolstation.com/help-and-advice/how-to-guides/how-to-remove-radiator?gad_source=1&gad_campaignid=19747119835&gclid=CjwKCAiAkvDMBhBMEiwAnUA9BR26YwBA6kOfcR4-JVxfJEjWdhRk6j0imCNcsIfu064wHN54-cs10xoCZ4cQAvD_BwE Although this is for a pressurised (combi) system where you need to get it back to pressure.  Pretty simple.  I don't bother with jointing compound.    
    • Fair enough - I'm absolutely wrong on that one. 👍
    • I'm still completely unclear what happened, apart from that a car apparently crashed into a lamp post opposite the Co-op. I presume the one in Lordship Lane, though the OP doesn't say. Was it speeding? Did it swerve to avoid someone who ran into the road? Did something go wrong with its brakes or steering? Did the driver have a medical emergency or fall asleep or got  distracted by something? Was there something slippery on the road surface? Was the driver hurt? Were any passengers hurt? Were any pedestrians or other road users hurt? Were there any witnesses? 
    • confused by the question?
Home
Events
Sign In

Sign In



Or sign in with one of these services

Search
×
    Search In
×
×
  • Create New...