Jump to content

Recommended Posts

Hi, I have to get a skip, builder wants to take everything out on Saturday and the parking restrictions state Mon-Fri. You have to suspend a bay to put a skip there now in Southwark if it has restricted parking but is that only on the days that they have the restrictions? I am hoping not to have to suspend ghe bay because it requires 10 days prior notice. Yes, did call parking, pressed the 'Suspending a bay' option and the guy who answered had no clue, ditto his manager :(
Y are u getting a skip normally the builder deals with skips permits etc I recently had some work done and the builder dealt with all that he used a company that brought the skip Saturday morning at 9 and waited till it was loaded approximately a hour saved a lot of hassle
Most skip companies organise the licence for you. In fact I think they're required to under Southwark byelaws. The skip company has to be registered with Southwark. But the Saturday delivery may well be your bigger obstacle as has been pointed out.
This is a separate issue to skips licences, this is an additional admin thing from Southwark- the need to suspend a parking bay which delays you for a further ten days. I got my answer from Southwark finally though- even if you want the skip on a Saturday when there are no parking restrictions you still have to pay to suspend the bay as if it were a Mon/Tues etc. Doesn't make any sense but I guess it brings in money for the council The extra ten day delay is more annoying than the extra cost thing. Thanks everyone for your input.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Discussions

    • If you want to change a radiator and it is the same size, pretty straight forward.  isolate by turning the two valves, one is straight forward hand twist, the other side you need to take the cap off and get an adjustable spanner and turn till closed.  Both clockwise. Use the same spanner to undo the large nuts that fix the radiator to the pipework, open the bleed valve, get a flatish container to catch the water which is likely to be a grotty black, sheets/plastic underneath to protect floor/floor covering.  Then jiggle off, tipping as quick as you an into your water container. Fingers crossed it will be the same back plate fitting.  If not you will have to take the old one off and fix the new one. Replacement is a reverse, allowing the rad to refill and let the air out. No naked flames involved. If it is a different size I can advise on that too. Lots on line too: https://www.toolstation.com/help-and-advice/how-to-guides/how-to-remove-radiator?gad_source=1&gad_campaignid=19747119835&gclid=CjwKCAiAkvDMBhBMEiwAnUA9BR26YwBA6kOfcR4-JVxfJEjWdhRk6j0imCNcsIfu064wHN54-cs10xoCZ4cQAvD_BwE Although this is for a pressurised (combi) system where you need to get it back to pressure.  Pretty simple.  I don't bother with jointing compound.    
    • Fair enough - I'm absolutely wrong on that one. 👍
    • I'm still completely unclear what happened, apart from that a car apparently crashed into a lamp post opposite the Co-op. I presume the one in Lordship Lane, though the OP doesn't say. Was it speeding? Did it swerve to avoid someone who ran into the road? Did something go wrong with its brakes or steering? Did the driver have a medical emergency or fall asleep or got  distracted by something? Was there something slippery on the road surface? Was the driver hurt? Were any passengers hurt? Were any pedestrians or other road users hurt? Were there any witnesses? 
    • confused by the question?
Home
Events
Sign In

Sign In



Or sign in with one of these services

Search
×
    Search In
×
×
  • Create New...